Download Article

Download Article

An analog clock tells you time past moving easily to point at numbers, rather than displaying numbers.[one] Analog clocks usually utilize a system of dials that you turn in order to move these hands. Sometimes these dials can be difficult to locate and understand. Y'all may need to experiment in order to empathize your clock a little meliorate and change the time.

  1. 1

    Alter the battery. If you lot have to reset your clock, information technology'due south likely that you need a new battery before doing so. Your batteries are usually found in a small box on the back of the clock. If in that location is no battery box on the back of the clock, a small rectangular hole in an indented rectangle is a practiced sign of a battery pack.

    • If there is no battery inside your clock, most battery packs have embossed messages inside the battery spaces telling you what size batteries to go.
  2. 2

    Notice the dials. Dials are unremarkably located at the back of the clock. Sometimes you may accept to remove a battery cover in society to get access to the dials on your clock.

    • If your clock has an alarm or a calendar, you may find that it has many dials. Your dials may have arrows or diagrams next to them that indicate their role.

    Advertisement

  3. 3

    Learn how the dials work. You can effigy out how the dials work past experimenting. Plow the dials, and so run into what happens on the face of the clock.

    • You lot should choose a dial and put your fingers on it firmly. Then turn the clock effectually so that you can see the hands moving, and turn the dial to effigy out which hand it is connected to. There are a number of variables that tin bear on the office of the dials, and so try to experiment: turn them both directions, and lift them or pull them out to encounter if this changes which hand engages.
    • Some clocks will use one punch for each hand. Other clocks will accept i dial that moves both hands. There may also be a dial to set an alarm, which is usually a smaller hand that is a different colour than the other ones.
  4. 4

    Set the clock. Check a phone or computer to find the electric current time. [2] News and atmospheric condition channels oftentimes brandish the fourth dimension besides.

  5. Advertisement

  1. 1

    Modify the bombardment. If your watch has stopped, yous may need to change the battery. [three] You can detect watch batteries at Radio Shack or Walmart, or y'all may desire to accept your sentinel back to the place that you lot bought information technology for a professional set.

    • You can potentially scratch your watch if you effort to replace your battery yourself. Withal, if you do want to pry off the back of your lookout, you can do and then with a small flat-head jeweler's screwdriver. Insert the tip of the screwdriver into the indentation or tab that separates the front and dorsum of your spotter. Tap it with a hammer or rubber mallet until the back comes off. Yous should then exist able to replace the bombardment (use a not-metal object to remove and supplant the battery) and the back of the picket.[4]
    • If your watch is solar powered or move powered, yous may need to charge it in the sun, or wear it for a day or ii before information technology is ready to set up.
  2. 2

    Notice the crown on your watch. This is the pocket-size knob on the side of your watch. Depending on how complicated your watch is, you may accept buttons instead of a crown.

  3. iii

    Pull out the crown. On some watches, the crown will pull out to multiple levels. Usually, 1 level will modify the date, and another level will change the time.

    • Experiment by pulling the crown out to multiple levels and turning information technology. If it doesn't affect the infinitesimal mitt and 60 minutes paw, pull it out or push it in to a different level.
  4. 4

    Set the time. Turn the crown until the minute mitt and hour paw are pointing to the right places.

    • Usually the minute and hour hands will movement together.
  5. 5

    Push the crown in. This volition set the time, and your watch volition start running once again.

    • Make sure that crown is pushed all the way in. If you don't push it all the way in, your spotter will non restart.
  6. Advertisement

Add together New Question

  • Question

    How tin I set the appointment on an analog sentry?

    Community Answer

    Button the crown by 1/2 full length, rotate to set the appointment on the sentry from one - 31. Experiment to figure out AM/PM.

  • Question

    Is it okay to turn the hands backward a full hr?

    Community Answer

    Yes, it is okay. Even so, make sure that information technology is set for the right time.

  • Question

    How do inset an alarm on an analog, twin bell clock?

    C Grace

    Look carefully on the back of the clock. Y'all should see a dial which moves the small alarm mitt. Y'all should besides meet a knob which pulls out and pushes in. They may take a small bell carved into the metallic below to indicate it woksk the alarm. Utilize the dial to move the piddling warning arrow, then pull the alarm knob out. When the alarm goes off, push it back in.

Enquire a Question

200 characters left

Include your email address to get a bulletin when this question is answered.

Submit

Ad

  • If yous are having a lot of trouble finding the dials on your clock, search the brand and make of your clock. Frequently, companies will publish their watch or clock manuals online.

Thanks for submitting a tip for review!

Ad

References

About This Commodity

Cheers to all authors for creating a page that has been read xc,876 times.

Did this article aid you lot?